電動擊實儀/土工電動擊實儀/電動擊實儀/多功能電動擊實儀價格
YDT-II型多功能電動擊實儀，電動擊實儀，擊實儀，多功能電動擊實儀
主要技術指標
1．擊錘重量： 4.5kg（重型擊實）； 2.5Kg（輕型擊實）
2．擊錘落高： 450mm（重型擊實）； 300mm（輕型擊實）
3、錘擊次數：30次/分
4、電機功率：三相550W
使用方法
1、接好電源線，合上電源開關，顯示屏顯示GOOD。
2、把控制器“移停”開關拔至“移動”位置。
3、轉動工作臺前擋架上的換位檔塊，使其短邊處于工作位置，插好定位銷。
4、安裝好φ152毫米試筒，并加入*層填料，按數字鍵輸入每層擊實次數，并正確顯示在顯示屏上。
5、按“啟動”鍵，儀器開始工作，每當落錘計數為7的倍數時，工作臺向后移動一次以保證擊實錘落在試筒的中心位置，*層擊實后儀器自動停機。
6、做第二層擊實時，添加填料后，直接按“啟動”鍵，儀器開始工作，第三層操作方法與此相同，可準確完成試件制作。
7、按“暫停”鍵可實現隨時停機，不影響連續計數，按“啟動”鍵可繼續工作，暫停工作時不可使壓桿裝置處于壓緊位置。
8、制作φ100毫米試件時，轉動工作臺前擋架上的換位檔塊，使其長邊處于工作位置，并插好定位銷，把控制器上“移停”開關拔至“停”位置，其它步驟同制作φ152毫米試件一樣。
主要用途
主要用于公路、鐵路、水利、建筑地基填土工程設計，以標準擊實方法在一定的擊實功下，測定土的含水量與干密度之關系，以確定該土的*含水量與相應的zui大干密度。
安裝與調試
1．將本機放置在平整的水平面上。
2．將主機上伸出的導線接到控制器后面板的輸出端。（10芯）
3．將電源線接到控制器后面板的輸入端。（4芯）
4．將電源線插頭插上電源上。
5．按下控制器上的置數/啟動鈕，使之處于置數狀態。
6．撥動置數盤，使之為03。
7．按下電源開/關鈕，電源接通。
8．按置數/啟動鈕，使之彈起，機器開始運轉。
9．待自動停機后，若擊實錘被提起，則接線正確，可正常工作；若擊實錘落在試筒內，則電機是反轉，應將電源插頭的任意兩根火線調換位置，再次試機，直到自動停機后擊實錘處于提起位置。
試驗規程
將制備好的試樣，分 3-5 次倒入筒內，每次將試樣倒入筒中 后，整平表面并把樣筒固定在機器上。
（1）152mm（大試筒）試樣：
① 按三層法，每次 800~900g 試樣（擊實后的試樣等于或略高于 筒的 1/3） ；按 5 層法時，每次約 400~500g（擊實后的試樣等于 或略高于筒的 1/5） 。
② 設備擊實次數；
③ 拔下旋轉插銷；
④ 關好主機護罩；
⑤ 按一下移臺按鈕，此時移臺指示燈亮，按下啟動按鈕，開始程序擊實。
（2）100mm（小試筒）試樣：
① 大筒按三層法時每層需試樣 1700g 左右，五層法時每層需試樣 900~1100g 左右
② 設定擊實次數。
③ 插入旋轉插銷；
④ 關好主機護罩；
⑤ 按一下移臺按鈕，此時移臺指示燈滅，按下啟動按鈕，開始擊實，此時機頭不旋轉，連續沿邊緣擊實。如擊實途中需停止擊 實或有其他不正常情況，按下暫停按鈕，機器停止工作。
| DZY-Ⅱ型數控多功能電動擊實儀 該儀器是根據交通部頒發的公路試驗行業標準研制的，其結構性能*符合（公路土工試驗規程）中的擊實試驗，（TO131－93）承載中比實驗 ，CBR）（TO134－93）回彈模量試驗（TO135－93）中的擊實試驗試樣制作要求，并具有輕型擊實和重型擊實兩種功能。 主要技術參數： 1、擊實錘重：重型：4.5kg 輕型：2.5kg 2、落錘高度：重型：450mm 輕型：300mm 3、錘擊次數：30次／分 4、電機功率：三相550W | ||
| LD127－Ⅱ型路強儀主機 | ||
| TLD-141型電動脫模器 此電動脫模器為可用于直徑為50mm,100mm,101.6mm,150mm,152mm高度為230mm以內的各種試模內試件脫模。 主要技術參數： 1、脫模器絲杠上升速度：70mm/min 2、脫模器絲杠下降速度：70mm/min 3、脫模器絲杠zui大移動距離：240mm 4、脫模器絲杠zui大上升極限距離：（L）270mm 5、脫模器絲杠zui大下降距離：（L）30mm 6、脫模器絲杠zui大脫模力：150KN | ||
| －2型光電液塑限聯合測定儀 本儀器采用光學投影，電磁頭自動落錐，能直接測讀0－22毫米圓錐入土深度，是土木工程、基本建設的*儀器。 主要技術參數 1、 圓錐儀總重：76g±0.2g和100g±0.2g 2、 圓錐角度：30°±0.2° 3、 測讀入土深度：0－22mm 4、 測讀精度：0.1mm，估讀0.05mm 5、 圓錐下落至讀數顯示時間：5秒 6、 電磁吸力：＞100g 7、 電源：交流220V10％ 8、 消耗功率：25W | ||
| ZBSX－92A型震擊標準振篩機 該機適用于公路、建筑、地質冶金科研等部門的試驗對物料進行篩分分析，每次開機5分種，既方便又簡單完成分級工作： 主要技術參數： 1、篩子直徑：300mm 200mm 2、震幅： 8mm 3、振擊次數：147次／分 4、篩搖動次數：221次／分 5、回轉半徑：12.5mm | ||
瀝青試驗儀器 土工路面試驗儀器 混凝土 水泥儀器 防水卷材試驗儀器 工程塑料試模產品有：養護箱, 標養箱, 混凝土滲透儀, 混凝土鉆孔取芯機, 混凝土自落式攪拌機, 水泥電動抗折試驗機, 行星式水泥膠砂攪拌機, 產品廣泛應用于大專院校、公路鐵路、橋梁隧道、石油化工、水利建設、國防等領域。在生產銷售自主產品的同時，我廠與國內外各名優廠家一直保持著良好的協作關系，代理銷售其品牌產品，價格比廠價更優惠，我們能讓廣大客戶朋友以低廉的價格使用到更優質的產品 主營產品：混凝土標準養護箱 | 水泥標準養護箱 | 混凝土抗滲儀|混凝土鉆孔取芯機 水泥凈漿攪拌機|水泥膠砂攪拌機 河北鼎盛路達實驗儀器設備廠 同時供應瀝青試驗儀器 土工路面試驗儀器 混凝土 水泥儀器 防水卷材試驗儀器 工程塑料試模，并為你組建各種實驗室。商砼攪拌站試驗儀器--商砼攪拌站混凝土試驗儀器
電 話：
電 話：
傳 真：
手 機：
：張
郵 箱：dingshengludayiqi
網 址：http://www.dsldyq.com/ http://www.yanwenjixie.com/
http://www.chem17.com/st230850
地 址：河北獻縣南河頭工業開發區18號
lectric compaction meter/geotechnical electric compaction meter/electric compaction meter/multi-function electric compaction meter price
YDT - type II multi-functional electric compaction meter, electric compaction meter, compaction meter, the multi-function electric compaction instrument
The main technical index
1. The hammer weight: 4.5 kg （heavy compaction）; 2.5 Kg （light compaction）
2. The hammer down high: 450 mm （heavy compaction）; 300 mm （light compaction）
3, hammer number: 30 times/points
4, motor power: the three-phase 550 w
Method of use
1, answer GOOD power cord, and closed the power switch, screen shows GOOD.
2, the controller "shift stop" switch drawn to "" position.
3, rotational work on the judgment seat in the transposition block, make its short edge in the job position, inserted positioning pin.
4, installed phi 152 mm test tube, and to join the first layer packing, press numeric key input of each layer of the compaction times, and will display correctly to the screen.
5, press the "start" button, the instrument began to work, when drop counter for 7 multiple, table move back a to ensure that the compaction hammer falls in the test tube of the center, the first layer after compaction instrument automatic stop.
6, do the second strike real-time, add packing, direct press the "start" button, the instrument work to begin, the third method of operation and the same, can accurate finish specimen making.
7, press the "stop" button can be realized at any time stop, do not affect continuous count, press the "start" button can continue to work, suspend work make pressure rod device in pressure position.
8, production phi 100 mm specimen, rotational work on the judgment seat in the transposition block, make its long side in working position, and inserted positioning pin, the controller "shift stop" switch drawn to "stop" position, other steps with making phi 152 mm as specimen.
The main purpose
Mainly used in highway, railway, water conservancy, construction foundation filling engineering design, a standard compaction method in certain compaction work, determination of soil water content and the relationship between dry density, in order to determine the optimum moisture content of soil and the corresponding maximum dry density.
Installation and debugging
1. The machine will be placed in the formation of the horizontal plane.
2. Will host outstretched wires to the output of the controller rear panel. （10 core）
3. The power cable received after the input panel controller. （4 core）
4. Will plug in the power cord on the power supply.
5. Press the controller on the load/start button, make in load condition.
6. Toggle device number plate, and make them work for 03.
7. Press the power on/off button, power on.
8. According to load/start button, the bounce, machine start running.
9. Stay automatic stop, if compaction hammer mentioned, the connection is correct, but normal work; If the compaction hammer falls on trial in the cylinder, the motor is reversal, should will power plug of any two root burn exchange position, commissioning again, until after the automatic stop compaction hammer in a position.
Test code
Will good sample preparation, divided into 3-5 times in the cylinder, each time will sample into cylinder, the whole flat surface and the sample tube fixed to the machine.
（1） 152 mm （large test tube） sample:
（1） according to the three layer method, every time 800 ~ 900 g sample （compaction of sample equal or slightly higher than 1/3 of the cylinder）; According to the five layer method, every time about 400 ~ 500 g （compaction of sample equal or slightly above the barrel of 1/5）.
（2） the equipment compaction times;
（3） pulled out rotary pin;
（4） closed host shield;
（5） according to a move down table button, the shift table indicator, press the start button, start program compaction.
（2） 100 mm （underbrush barrel） sample:
（1） the big drum according to the three layer method of every layer need to sample 1700 g or so, five layer method of every layer need to sample 900 ~ 1100 g or so
（2） setting compaction times.
（3） insert rotary pin;
（4） closed host shield;
（5） according to a move down table button, the shift table lamp out, press the start button, and began to compaction, the head not rotating, continuous along the edge compaction. The way to stop such as compaction compaction or have other abnormal situation, press the stop button and the machine stop working.
1. The hammer weight: 4.5 kg （heavy compaction）; 2.5 Kg （light compaction）
2. The hammer down high: 450 mm （heavy compaction）; 300 mm （light compaction）
3, hammer number: 30 times/points
4, motor power: the three-phase 550 w
Method of use
1, answer GOOD power cord, and closed the power switch, screen shows GOOD.
2, the controller "shift stop" switch drawn to "" position.
3, rotational work on the judgment seat in the transposition block, make its short edge in the job position, inserted positioning pin.
4, installed phi 152 mm test tube, and to join the first layer packing, press numeric key input of each layer of the compaction times, and will display correctly to the screen.
5, press the "start" button, the instrument began to work, when drop counter for 7 multiple, table move back a to ensure that the compaction hammer falls in the test tube of the center, the first layer after compaction instrument automatic stop.
6, do the second strike real-time, add packing, direct press the "start" button, the instrument work to begin, the third method of operation and the same, can accurate finish specimen making.
7, press the "stop" button can be realized at any time stop, do not affect continuous count, press the "start" button can continue to work, suspend work make pressure rod device in pressure position.
8, production phi 100 mm specimen, rotational work on the judgment seat in the transposition block, make its long side in working position, and inserted positioning pin, the controller "shift stop" switch drawn to "stop" position, other steps with making phi 152 mm as specimen.
The main purpose
Mainly used in highway, railway, water conservancy, construction foundation filling engineering design, a standard compaction method in certain compaction work, determination of soil water content and the relationship between dry density, in order to determine the optimum moisture content of soil and the corresponding maximum dry density.
Installation and debugging
1. The machine will be placed in the formation of the horizontal plane.
2. Will host outstretched wires to the output of the controller rear panel. （10 core）
3. The power cable received after the input panel controller. （4 core）
4. Will plug in the power cord on the power supply.
5. Press the controller on the load/start button, make in load condition.
6. Toggle device number plate, and make them work for 03.
7. Press the power on/off button, power on.
8. According to load/start button, the bounce, machine start running.
9. Stay automatic stop, if compaction hammer mentioned, the connection is correct, but normal work; If the compaction hammer falls on trial in the cylinder, the motor is reversal, should will power plug of any two root burn exchange position, commissioning again, until after the automatic stop compaction hammer in a position.
Test code
Will good sample preparation, divided into 3-5 times in the cylinder, each time will sample into cylinder, the whole flat surface and the sample tube fixed to the machine.
（1） 152 mm （large test tube） sample:
（1） according to the three layer method, every time 800 ~ 900 g sample （compaction of sample equal or slightly higher than 1/3 of the cylinder）; According to the five layer method, every time about 400 ~ 500 g （compaction of sample equal or slightly above the barrel of 1/5）.
（2） the equipment compaction times;
（3） pulled out rotary pin;
（4） closed host shield;
（5） according to a move down table button, the shift table indicator, press the start button, start program compaction.
（2） 100 mm （underbrush barrel） sample:
（1） the big drum according to the three layer method of every layer need to sample 1700 g or so, five layer method of every layer need to sample 900 ~ 1100 g or so
（2） setting compaction times.
（3） insert rotary pin;
（4） closed host shield;
（5） according to a move down table button, the shift table lamp out, press the start button, and began to compaction, the head not rotating, continuous along the edge compaction. The way to stop such as compaction compaction or have other abnormal situation, press the stop button and the machine stop working.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
DZY - Ⅱ type nc multi-function electric compaction instrument
This instrument is issued by the ministry of communications according to road test industry standard development, the structure performance fully comply with （highway soil test code） of the compaction test, （TO131-93） bearing than experiment, CBR） （TO134-93） modulus of resilience test （TO135-93） of the compaction test sample production requirements, and has light compaction and heavy compaction two functions.
Main technical parameters:
1, compaction hammer weight: heavy: 4.5 kg
Light: 2.5 kg
2, drop height: heavy: 450 mm
Light: 300 mm
3, hammer number: 30 times/points
4, motor power: the three-phase 550 w
1, compaction hammer weight: heavy: 4.5 kg
Light: 2.5 kg
2, drop height: heavy: 450 mm
Light: 300 mm
3, hammer number: 30 times/points
4, motor power: the three-phase 550 w
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
LD127 - Ⅱ type road strong instrument host
Pavement material strength tester host is a kind of multi-function highway roadbed, road surface material test instrument. Can be used to test various adhesive material stabilized soil specimen of have no limit of measuring the compressive strength, the determination of soil and pavement material bearing ratio （CBR）, determination of asphalt mixture thermal stability and resistance to plastic flow performance - stability and flow value.
Main technical parameters:
1, maximum load rating: 100 kn
2, screw plate maximum lifting distance: 200 mm
3, motor speed: fast: 50 mm/min
Slow: 1 mm/min
4, manual speed: 1/6 / crank each lap
1, maximum load rating: 100 kn
2, screw plate maximum lifting distance: 200 mm
3, motor speed: fast: 50 mm/min
Slow: 1 mm/min
4, manual speed: 1/6 / crank each lap
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
上一篇： 混凝土抗滲儀/混凝土抗滲儀操作規程
